WorldNet Knowledgebase

VoIP ATA Setup Guide: Linksys PAP2NA

| Analog Telephone Adapter (ATA) is a device for connecting traditional analogue telephones to a voice-over IP (VoIP) telephone network.

Step-1. Connect the ATA device

Step-2. Access the ATA device

(1) Check the IP address of the ATA device

- Dial **** (four asterisks) > Dial 110# > Get the IP address (e.g. 192.168.1.202)

(2) Open a web browser and type the IP address

Step-3. Setup the ATA device

(1) Click [Admin Login]

Note that after clicking [Admin Login], it is changed to [User Login].

(2) Click [Line 1], and then click [(switch to advanced view)]

Note that after clicking [(switch to advanced view)], it is changed to [(switch to basic view)].

(3) Line 1 Settings

Note that leave the default settings as is, except for the changes listed below:

[Streaming Audio Server (SAS)] ==============

Line Enable: yes

[NAT Settings] ==============

NAT Keep Alive Enable: yes

[Network Settings] ==============

Skipped

[SIP Settings] ==============

Skipped

[Call Feature Settings] ==============

Skipped

[Proxy and Registration] ==============

Proxy: sip.feenix.co.nz

Proxy Fallback Intvl: 600

[Subscriber Information] ==============

Display Name: Phone Number (e.g. 6498200003)

User ID: Phone Number (e.g. 6498200003)

Password: xxxxxxx (case-sensitive)

Use auth ID: no

[Suppliementary Service Subscription] ==============

Block CID Serv: no

Block ANC Serv: no

Cfwd All Serv: no

Cfwd Busy Serv: no

Cfwd No Ans Serv: no

Cfwd Sel Serv: no

Cfwd Last Serv: no

Block Last Serv: no

Accept Last Serv: no

DND Serv: no

Call Return Serv: no

Speed Dial Serv: no

[Audio Configuration] ==============

Preferred Codec: G729a

Fax Passthru Codec: G711a

FAX Passthru Method: ReINVITE

[Dial Plan] ==============

Dial Plan: (*xx.|111S0|[2-9]xxxxxxS0|00xx.|02xx.|0[34679]xxxxxxxS0|0508x.|08xx.|09xx.|05xx.|01xx.|11[023456789]xx.)

Enable IP Dialing: no

[FXS Port Polarity Configuration] ==============

Skipped

==========================================

(4) Click [Save Settings]

(5) Click [Regional]: Regional Settings

Note that leave the default settings as is, except for the changes listed below:

[Call Progress Tones] ==============

Dial Tone: 400@-9;30(*/0/1)
Second Dial Tone: 420@-19,520@-19;10(*/0/1+2)
Outside Dial Tone: 420@-16;10(*/0/1)
Prompt Tone: 520@-19,620@-19;10(*/0/1+2)
Busy Tone: 400@-9;*(.5/.5/1)
Reorder Tone: 400@-9;15(.25/.25/1+2)
Off Hook Warning Tone: 400@-10,680@0;*(.125/.125/1+2)
Ring Back Tone: 400@-19,450@-19;*(.4/.2/1+2,.4/.2/1+2,2/0/0)
Confirm Tone: 600@-16;1(.25/.25/1)
SIT1 Tone: 985@-16,1428@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)
SIT2 Tone: 914@-16,1371@-16,1777@-16;20(.274/0/1,.274/0/2,.380/0/3,0/4/0)
SIT3 Tone: 914@-16,1371@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)
SIT4 Tone: 985@-16,1371@-16,1777@-16;20(.380/0/1,.274/0/2,.380/0/3,0/4/0)
MWI Dial Tone: 400@-19;2(.1/.1/1);28(*/0/1)
Cfwd Dial Tone: 350@-19,440@-19;2(.2/.2/1+2);10(*/0/1+2)
Holding Tone: 600@-19;*(.1/.1/1,.1/.1/1,.1/9.5/1)
Conference Tone: 350@-19;20(.1/.1/1,.1/9.7/1)
Secure Call Indication Tone: 397@-19,507@-19;15(0/2/0,.2/.1/1,.1/2.1/2)

[Distinctive Ring Patterns] ==============

Ring1 Cadence: 60(.4/.2,.4/2)
Ring2 Cadence: 60(.4/.8,.4/14)
Ring3 Cadence: 60(.8/.4,.8/4)
Ring4 Cadence: 60(.4/.2,.3/.2,.8/4)
Ring5 Cadence: 60(.2/.2,.2/.2,.2/.2,1/4)
Ring6 Cadence: 60(.2/.4,.2/.4,.2/4)
Ring7 Cadence: 60(.4/.2,.4/.2,.4/4)
Ring8 Cadence: 60(0.25/9.75)

[Distinctive Call Waiting Tone Patterns] ==============

CWT1 Cadence: 30(.3/9.7)
CWT2 Cadence: 30(.1/.1, .1/9.7)
CWT3 Cadence: 30(.1/.1, .3/.1, .1/9.3)
CWT4 Cadence: 30(.1/.1,.1/.1,.1/9.5)
CWT5 Cadence: 30(.3/.1,.1/.1,.3/9.1)
CWT6 Cadence: 30(.1/.1,.3/.2,.3/9.1)
CWT7 Cadence: 30(.3/.1,.3/.1,.1/9.1)
CWT8 Cadence: 2.3(.3/2)

[Distinctive Ring/CWT Pattern Names] ==============

Skipped

[Ring and Call Waiting Tone Spec] ==============

Ring Waveform: Sinusoid
Ring Frequency: 25
Ring Voltage: 70
CWT Frequency: 400@-10
Synchronized Ring: no

[Control Timer Values(sec)] ==============

Skipped

[Vertical Service Activation Codes] ==============

Skipped

[Vertical Service Announcement Codes] ==============

Skipped

[Outbound Call Codec Selection Codes] ==============

Skipped

[Miscellaneous] ==============

Set Local Date (mm/dd): Set current month and day
Set Local Time (HH/mm): Set current hour and minute
Time Zone: GMT+12
FXS Port Impedance: 220+820|120nF
Daylight Saving Time Rule: start=10/1/7/2;3/15/7/3;save=1
FXS Port Input Gain: -4
FXS Port Output Gain: -10
DTMF Playback Level: 0
DTMF Playback Length: .1
Detect ABCD: no
Playback ABCD: yes
Caller ID Method: Bellcore(N.Amer,China)
FXS Port Power Limit: 4